Valtra error codes (also known as fault codes or DTCs) help identify issues within the tractor's engine, transmission, or electronic systems. When a fault occurs, a code—typically a combination of letters and numbers—appears on the instrument panel or A-post display s02bac55f730da904.jimcontent.com Common Valtra Error Codes & Descriptions
Fault codes are categorized by the system they affect. Below are examples of codes found in Valtra diagnostic manuals: P101 / P103 / P105 : Issues with the DPS (Delta Powershift)
proportional valves (P1, P2, or P3). This usually indicates a short circuit or wire damage. P107 / P109 : Faults in the Forward or Reverse drive
proportional valves. These often point to wiring issues or electrical limits being exceeded. A311 / A312 Gearbox oil temperature sensor (B14) errors. A311 indicates temperature over , while A312 indicates a reading below , suggesting a faulty sensor or wiring.
: Often seen on older models (like the T170), this code can indicate hydraulic or transmission issues , sometimes caused by low oil levels. 110 / 111 / 112 Engine coolant temperature
sensor defects. 110 (Low), 111 (High), and 112 (High temperature alarm). Fuel rail pressure
issues. 381 indicates low rail pressure, while 382 indicates high pressure. 007200 / 007202 Hydrostatic unit errors, such as overheating ( ) or excessive pressure due to heavy loads. s02bac55f730da904.jimcontent.com Fault Levels & Power Limits
Many engine-related codes (EEM3) trigger safety modes to protect the tractor: : Fuel Limit 1 (Power reduced to : Fuel Limit 2 (Power reduced to ) and Speed Limit (often : Fuel Cutting to zero (Engine shutdown). How to Access and Clear Codes Accessing the Menu
: On many models, you can retrieve codes through the diagnostic menu on the display panel. For specific series, this may involve holding specific icons (like a book or hourglass) to enter the service menu. Active vs. Inactive Active faults are currently occurring and may trigger warning lights. Inactive faults
are historical events stored in the system's memory and can help with long-term troubleshooting.
: While some service reminders can be reset via the A-post (e.g., setting "Light Service" hours to
), critical fault codes usually require the underlying issue to be repaired before they can be cleared using a diagnostic tool. VALTRA FAULT CODES
Valtra error codes (also known as fault or service codes) are used to diagnose issues with the tractor's engine, transmission, and hydraulic systems. These codes typically appear on the dashboard or A-pillar display and are often categorized by the system they affect. Common Valtra Error Codes
Codes are often divided into groups like Engine (EEM), Transmission (HiTech/Versu), and Hydraulics (Autocontrol). Engine & Fuel (EEM3 Codes):
E31: High fuel pressure/system impact. Often caused by air in the system or a faulty pressure relief valve. 110/111: Coolant temperature sensor defect (Low/High). 98/99: Low engine oil pressure alarm. 251/252: Fuel temperature sensor defect. Transmission & Power Shuttle: F320: Park/start circuit failure (always off). F322: Park brake pressure switch open.
P101–P109: Issues with DPS proportional valves (short circuits or wiring damage).
A311/A312: Gearbox oil temperature sensor values out of range (Too high/low). 007200: Hydrostatic unit overheating. Hydraulics & Linkage: 1010: Hitch Up/Down switch failure in the armrest.
4019/4029: Draft Pin voltage outside normal range (Right/Left). 9317: Hitch controller calibration required. How to Retrieve Codes
On modern models like the N4 and T4 Series, you can access diagnostics through the dashboard menu. Use the Set button to enter the menu and navigate with the arrow keys to find stored fault codes in the A-pillar display. Detailed technical guides for specific models are available on platforms like Scribd and Valtra's official site.
Do you have a specific code appearing on your display right now? VALTRA FAULT CODES
The Digital Language of Modern Farming: Understanding Valtra Error Codes
In the landscape of modern agriculture, a tractor is no longer just a mechanical workhorse; it is a sophisticated mobile computer. For owners of Valtra machinery, the appearance of a service code on the Tractor Health screen is the first line of communication between the machine’s Electronic Control Units (ECUs) and the operator. These codes serve as a diagnostic roadmap, identifying issues ranging from simple sensor misreads to critical transmission failures. The Diagnostic Architecture
Valtra tractors utilize a structured error code system where each alphanumeric string corresponds to a specific subsystem and fault type.
Prefixes and Systems: Codes often start with letters indicating the affected system, such as "P" for powertrain (engine and transmission), "C" for chassis, and "A" for Autocontrol or auxiliary systems. Specific Subsystems:
Transmission (TCU): Codes like F320–F322 often indicate issues with the transmission control unit or park brake systems during startup.
Engine (EEM): Engine-related codes, often labeled under the EEM3 or Sisu Diesel standards, track critical metrics like coolant temperature (e.g., code 110/111) and rail pressure (e.g., code 381).
Hydraulics: Codes such as E290 or E393 frequently point toward hydraulic system malfunctions or sensor communication failures. Interpreting Common Faults
Many Valtra error codes relate to electrical integrity, such as short circuits or wire damage in proportional valves (e.g., codes P101–P109). Others alert the operator to operational inconsistencies:
A313/A314: Indicates the gas or clutch pedal position sensors are sending signals outside the allowable voltage range (1V to 7V DC).
A335: Often appearing in models like the T170, this code typically signals hydraulic or transmission issues potentially linked to low oil levels.
Battery/Voltage: Codes like 33 (low voltage) or 17 (excessive voltage) warn of electrical supply issues that can cause erratic behavior across all electronic modules. Responding to Codes
When an error code appears, Valtra's official operator guidance suggests a tiered response:
Valtra Tractor Error Codes Guide | PDF | Clutch | Throttle - Scribd
Functions on the top line: 6 Control for: --- Driving trip m, km / miles. --- main/dipped headlights. --- direction indicators --- VALTRA FAULT CODES
Learning Valtra error codes transforms a flashing warning light from a panic moment into a simple diagnostic checklist. While codes like MID 136 or SPN 3362 sound intimidating, 80% of them stem from three causes: fuel contamination, low battery voltage, or a dirty sensor.
Your cheat sheet:
If you encounter a code not listed here (e.g., SPN 5246 FMI 13), write down the full 9-digit sequence and contact your Valtra dealer with that number. Modern ECUs store time-stamped data – technicians can see exactly what RPM and temperature the fault occurred at.
Disclaimer: Always refer to your specific model’s service manual. Working on common rail fuel systems or SCR components requires specialized training.
Keywords integrated: valtra error codes, al 414 valtra, spn 94 valtra, valtra fault code list, valtra blink codes, valtra dtc, valtra transmission error, valtra adblue code.
If your tractor has no digital screen, you can use a jumper wire on the diagnostic port (typically near the fuse box) and count the flashes of the check engine light.
Important: Always write down the code before clearing it. If you disconnect the battery without recording the code, you lose the diagnostic history.
Valtra error codes are not punishments; they are conversations. Your tractor is telling you exactly what is wrong—if you speak the language. A flashing SPN 100 is not a mysterious breakdown; it’s a command: “Check my oil pressure.”
By keeping this guide handy, learning how to access the diagnostic menu on your specific model, and performing basic troubleshooting steps, you can save hundreds of hours of downtime and thousands in repair bills.
Final Checklist When You See a Valtra Code:
Treat your Valtra’s error system as the intelligent partner it is, and your tractor will serve you reliably for 10,000+ hours. Now go decode that dashboard.
Disclaimer: This article is for informational purposes. Always refer to your specific Valtra model’s operator manual and factory service literature. When in doubt, consult an authorized Valtra service center.
Here is a curated list of frequently encountered Valtra error codes. Note: Always cross-reference with your specific model’s service manual, as codes can vary by software version.
While there are hundreds of potential codes, they generally fall into three main categories based on severity.
Goal: Ship an in-product feature that helps users identify, interpret, and act on Valtra tractor error codes quickly and safely.
Key user problems solved
Core functionality (MVP)
Advanced features (post-MVP)
Data & sources
UX flow (MVP)
Technical considerations
Safety & compliance
Rollout plan (8 weeks)
Metrics to track
Success criteria (90 days)
Risks & mitigations
Next steps
If you want, I can: produce UI mockups for the lookup/result card, draft the diagnostic checklist template, or draft the code data schema. Which deliverable do you want first?
Valtra error codes (also known as fault or service codes) are diagnostic indicators used to identify malfunctions in a tractor's engine, transmission, or electronic systems. When a fault is detected, a code appears on the instrument panel or "Tractor Health" screen to help operators troubleshoot the issue Common Valtra Error Codes
Codes are often categorized by the system they affect, such as the DPS (Delta Power Shift) EEM (Engine Electronic Management) , or rear linkage systems. Component / System Description of Issue Gas Pedal Sensor (B15) Signal voltage is out of range (below ); often due to a faulty sensor or damaged wiring. DPS Proportional Valve
Current for valve P1 is outside limits; typically indicates a short circuit or wire damage. Drive Train / Engine
Engine revs and drive train speed do not match; may feel like the transmission is "slipping". Hydraulic/Transmission
Often linked to low oil levels or issues within the hydraulic system. Engine Oil Pressure Indicates low oil pressure or a low oil pressure alarm. Engine Coolant High coolant temperature or a high temperature alarm. Rear Linkage Output/lifting valve is not connected.
Time-out error; control unit is not receiving messages via the CAN bus. Navigating Faults and Diagnostics
Understanding Valtra Error Codes: A Quick Guide for Operators
Modern Valtra tractors are highly advanced machines that use on-board diagnostics to alert you when something isn't right. When a code pops up on your Tractor Health screen, it is the machine's way of identifying a specific technical issue before it leads to a major breakdown. How to Access and Read Fault Codes
Retrieving these codes varies slightly depending on your model (A, N, T, S, or G Series), but general steps often include:
Checking the Display: Most modern Valtra tractors show active service codes directly on the main dashboard or the Tractor Health screen.
Navigating Menus: On models like the G Series, you can cycle through the service and settings menus using the right-hand arrow keys on the soft keypad.
Using Test Modes: Older or more technical systems (like Autocontrol 5) might require entering a specific "test mode" to view codes like d16 (Parking brake) or d05 (Driver detection). Common Valtra Error Codes and Meanings
Valtra codes are often categorized by the system they monitor. Below are some common codes found in technical manuals: Code Category Example Code What it Means Potential Fix Engine Sensors 110, 111 Coolant temp sensor defect (Low/High) Check sensor wiring and coolant levels. Transmission F320–F322 Park brake or start circuit issues Inspect pressure switches and TCU connections. Electronics 33, 17 Battery voltage too low or too high Check battery terminals and alternator output. Hydraulics 31, 32 Draft sensor signal faulty Inspect RH/LH side draft sensor connections. Drive System P101, P103 Proportional valve current issues Check for short circuits in the DPS solenoids. Immediate Troubleshooting Steps
If an error code appears while you are in the field, follow these standard operator procedures: Why Farmers Choose Valtra Tractors
Valtra tractors use a sophisticated diagnostic system that translates internal malfunctions into specific service codes or fault codes displayed on the instrument panel or the SmartTouch screen. Core Feature: "Live Diagnostic Translator"
If you are looking to "come up with a feature" for Valtra error codes, a highly useful integration would be a Live Diagnostic Translator within the Valtra Connect app. This feature would:
Instant Identification: Automatically pull active codes from the tractor's ECU via Bluetooth/CAN-bus and display a plain-English explanation of the fault.
Guided Troubleshooting: Provide step-by-step visual instructions (potentially via Augmented Reality) to locate the affected sensor or valve, such as the P101 proportional valve or the A311 gearbox oil temperature sensor.
Predictive Maintenance: Analyze historical data to alert you before a code appears, such as identifying a component that is beginning to take irregular current levels. Common Valtra Error Code Categories
Valtra codes are typically grouped by the system they affect:
Engine (EEM/EEM3): Focuses on sensors like coolant temperature (e.g., code 110) or fuel rail pressure (e.g., code 381).
Transmission/DPS: Codes like P101 or P107 indicate issues with proportional valves or drive solenoids.
Hydraulics/Linkage: Codes such as 31 or 32 (RH/LH draft sensors) often relate to wiring faults or sensor misalignments.
Instrument Panel/CAN-bus: Codes in the 300+ range (e.g., 301, 305) indicate communication failures between the cluster and specific controllers. How to Use Existing Features
Check the "Tractor Health" Screen: Modern Valtra models with SmartTouch display active service codes directly on the main interface.
Monitor Remotely: Use Valtra Connect to share diagnostic data with your local service center, allowing technicians to view codes and potentially repair faults or cancel codes remotely.
Manual Reset: If a code appears, the standard procedure is to stop the tractor, turn off the power, and restart; if it persists, professional diagnostic tools like Jaltest AGV or official dealer software are required for deep-level clearing and calibration. Valtra Connect learns to predict faults
Valtra tractors use a system of diagnostic fault codes to identify issues with the engine, transmission, and hydraulic systems. These codes are typically displayed on the dashboard's side pillar (AC 5 display) or the main instrument panel. Common Valtra Error Categories
Error codes are generally divided by the system they affect:
Engine (EEM3/Sisu) Codes: Focus on sensors, fuel delivery, and temperatures. 110/111: Coolant temperature sensor defect (Low/High). 98/99: Low oil pressure or low oil alarm. 121: Water in fuel detector alert.
Transmission & Shuttle Codes: Indicated by "F" or "L" prefixes.
F320/F322: Start-up problems usually related to the park brake switch or circuit not being engaged correctly.
L422: Shuttle direction engaged for over 3 seconds without full control.
Hydraulic & Rear Linkage (Flash Codes): Often displayed as "Service Codes". Flash Code 17: Battery voltage too high (over 19V). Flash Code 33: Battery voltage too low (under 8V).
Flash Code 37: Steering valve lift failure (linkage won't lift despite receiving current). Quick Reference Table Example Code Common Solution Engine 110 Coolant sensor defect Check sensor wiring and coolant levels. Engine 98 Low oil pressure Stop engine immediately; check oil levels. Transmission F320 Park/Start circuit off Ensure park brake is properly seated. Hydraulics E290 Hydraulic system fault Check fluid levels and unit connectors. Linkage Flash 22 Position sensor fault Inspect signal voltage/adjust sensor. How to Access and Interpret Codes
Retrieval: On newer models (like G, N4, or T4 Series), access the "Service Codes" menu via the side pillar buttons. This menu is often only visible when a code is active.
Visual Indicators: A flashing red "Stop" symbol on the dashboard indicates a critical fault, such as low oil pressure or alternator failure, requiring an immediate stop. valtra error codes
Diagnosis: For detailed troubleshooting, refer to the Valtra Fault Codes and Diagnostics Guide which details specific pin-outs and resistance values for technicians.
Note: Codes like E393 or E290 on T-series tractors often point to communication issues between the engine sensors and the hydraulic control unit.
Valtra Fault Codes and Diagnostics Guide | PDF | Clutch - Scribd
Title: Understanding Valtra Tractor Error Codes: A Guide to Diagnostics, Common Codes, and Troubleshooting
1. Introduction
Valtra, a Finnish brand owned by AGCO, is renowned for its rugged, highly customizable tractors featuring the unique "SmartTouch" interface and TwinTrac reverse drive. Like all modern agricultural machines, Valtra tractors rely on a complex network of Electronic Control Units (ECUs) to manage the engine, transmission, hydraulics, and emissions systems. When a fault occurs, the system generates an alphanumeric error code. This paper provides a structured overview of Valtra error codes, their formats, common examples, and recommended diagnostic procedures.
2. Error Code Format and Access
Valtra primarily uses two code formats, accessible via the instrument cluster or the SmartTouch screen:
Example Code Breakdown: MID 128 PID 94 FMI 1
Accessing Codes:
3. Common Valtra Error Codes by System
| System | Error Code | Description | Likely Cause |
| :--- | :--- | :--- | :--- |
| Engine & Emissions | SPN 97 FMI 3 | Water in Fuel Indicator – High Voltage | Water in fuel filter sensor faulty or actual water contamination. |
| | SPN 3242 FMI 4 | Aftertreatment Diesel Exhaust Fluid (DEF) Tank Level – Low Voltage | DEF tank level sensor failure or wiring short. |
| | SPN 4360 FMI 15 | SCR System – Reagent Dosing Valve – High Temperature | DPF regeneration interrupted or dosing valve stuck. |
| Transmission | MID 138 PID 177 | Transmission Fluid Temperature – Above Normal | Overloaded operation, low fluid, or cooler blockage. |
| | MID 140 SID 35 | CVT (Variomatic) Ratio Error | Clutch wear, pressure sensor fault, or calibration required. |
| Hydraulics/Electrics | MID 217 SID 247 | Rear Remote Valve – Position Sensor – Out of Calibration | Remote valve lever needs recalibration via SmartTouch. |
| | MID 144 PID 168 | Battery Voltage – Below Normal (FMI 1) | Alternator failure, loose belt, or dead cell. |
4. The Valtra FMI Code Quick Reference (SAE J1939)
Understanding the FMI is critical. Common FMIs on Valtra:
5. Troubleshooting Workflow
When an error code appears, follow this structured approach:
6. Limitations and Advanced Diagnostics
7. Conclusion
Valtra error codes are a powerful first step in diagnosing tractor faults, but they are not a repair manual. They direct the technician to a specific system and failure mode. By understanding the MID/PID/FMI logic and following systematic checks—starting with simple wiring and battery voltage—most non-emergency codes can be resolved. Persistent or drivability-related codes (e.g., transmission ratio errors) mandate dealer-level software and calibration tools.
Always keep an updated error code log. Frequent recurrence of a code (e.g., SPN 97 FMI 1 every 50 hours) points to a chronic underlying issue rather than a one-time glitch.
Disclaimer: This paper is for informational purposes. Always refer to the official Valtra service manual for your specific model year before performing repairs.
Title: Understanding Valtra Error Codes: A Diagnostic Guide for Operators
Valtra tractors, renowned for their Scandinavian durability and advanced technology, rely heavily on onboard computer systems to manage engine performance, hydraulics, and transmission. Like all modern agricultural machinery, when these systems detect a fault, they communicate via specific error codes.
Understanding these codes is essential for operators to distinguish between a minor glitch that can be resolved in the field and a serious system failure requiring a dealer visit. This guide provides an informative overview of how Valtra error codes function, common code categories, and troubleshooting steps.
(Obtain exact numeric-to-fault mappings from the Valtra service manual for your model.)
If you tell me your Valtra model and the exact code(s), I’ll provide a targeted diagnosis and step-by-step checks.
(functions.RelatedSearchTerms)
Valtra error codes (also known as Diagnostic Trouble Codes or DTCs) are the tractor's way of identifying specific mechanical or electronic malfunctions. These codes typically consist of a letter followed by a three or four-digit number, appearing on the dashboard display or through the Valtra Connect monitoring system. s02bac55f730da904.jimcontent.com Understanding Error Code Prefixes
The letter at the beginning of a code indicates which system is affected: P-Codes (Powertrain)
: Usually relate to the transmission, DPS (Delta Power Shift), and shuttle valves. A-Codes (Auxiliary/Analog)
: Often involve sensors like pedal positions (gas or clutch) and gearbox oil temperature. F-Codes (Faults/Functions)
: General system faults, including tachometer or speed sensor issues. L-Codes (Linkage) : Specific to the hydraulic lift or rear linkage systems. E-Codes (Engine/EEM)
: Relate to the Sisu Diesel engine management, such as fuel pressure or coolant sensors. s02bac55f730da904.jimcontent.com Common Valtra Error Codes & Meanings Likely Cause P101 / P103 DPS Valve Error
Proportional valve current exceeds or falls below limits (short circuit or wire damage). A311 / A312 Oil Temp Sensor
Gearbox oil temperature value is impossible (too high or too low), suggesting a faulty sensor. A313 / A314 Pedal Sensor
Signal from gas pedal (B15) or clutch pedal (B16) is outside the 1V–7V range. F320 / F322 Park Brake Issue
Park/start circuit is off or the park brake pressure switch is open during startup. E110 / E111 Coolant Temp Coolant temperature sensor defect (low or high signal). Shuttle Slip
Slipping in the multi-disc clutch or trapped proportional valves. Troubleshooting Steps If a code appears, follow these general steps: Decode the Fault : Check the specific code against the Valtra Technical Manual or the operator's handbook. Verify Connections
: Many errors are caused by loose or oxidized connectors. Check the wiring harness and sensor pins for damage. Use Test Mode
: Access the self-diagnosis menu (often by holding specific dashboard buttons) to test individual components like PTO switches or sensors in real-time. Clear and Reboot
: If the issue persists after physical checks, a software update or system reset via a diagnostic tool may be necessary.
For critical engine or transmission errors, it is recommended to contact an authorized service center, as some faults may trigger a "limp mode" to prevent further damage. specific button sequence
to enter the diagnostic menu for your particular Valtra model? VALTRA FAULT CODES
Understanding Valtra error codes is critical for maintaining uptime on your tractor, whether you're operating an N, T, S, or G Series model. These codes act as a diagnostic language between the tractor's Electronic Control Units (ECUs) and the operator, signaling issues ranging from simple sensor misalignments to critical engine or transmission failures. Common Valtra Error Code Categories
Valtra uses specific alphanumeric prefixes to help you identify which system requires attention:
P-Codes (Transmission/DPS): These generally relate to the Delta Powershift (DPS) and transmission proportional valves.
P101, P103, P105: Indicate current issues with proportional valves P1, P2, or P3. This often means a short circuit or damaged wiring.
P107 & P109: Signal faults with the forward and reverse drive proportional valves, often leading to a loss of drive direction. A-Codes (Sensors & General Systems):
A311 & A312: Indicate impossible gearbox oil temperature readings (either too high or too low), usually caused by a faulty sensor or wiring. Valtra error codes (also known as fault codes
A313: Highlights an issue with the gas pedal position sensor signal.
A335: Often seen on T-series models, this typically points toward hydraulic or transmission malfunctions, sometimes linked to low oil levels. F-Codes (Operational & Brake):
F320, F321, F322: These focus on the park brake system. For instance, F322 means the park brake pressure switch is open, indicating the brake isn't engaged during startup when it should be.
F324: Occurs when the driving speed exceeds 10 km/h while direction information is changing, possibly due to a slipping PTO clutch or a faulty RPM sensor. Engine (EEM) & Service Codes:
110–113: Critical engine coolant temperature codes. Code 113 is a high-temperature alarm that may trigger a shutdown.
98 & 99: Low oil pressure warnings; 99 is the critical alarm state.
E290 & E393: Commonly found on T121 models, these signify hydraulic system malfunctions or communication errors between sensors. How to Read Codes on the Dashboard
Modern Valtra tractors, like the G Series, feature a TFT dashboard screen that displays "Service Codes" on a dedicated Tractor Health screen. VALTRA FAULT CODES
The Valtra Error Codes feature is an in-product diagnostic tool designed to help operators identify, interpret, and resolve tractor faults quickly and safely. Key Capabilities
Rapid Identification: Translates numeric fault codes into clear text descriptions on the tractor's dashboard or terminal.
Actionable Guidance: Provides specific instructions on whether the issue can be fixed in the field or requires a service technician.
Safety Alerts: Categorizes errors by severity to prevent potential damage to the engine or transmission.
Remote Support: Often integrates with Valtra Connect to allow dealers to view error logs remotely for faster troubleshooting. Common Valtra Error Categories:
Transmission (e.g., P, F codes): Issues with shifting, oil pressure, or sensor synchronization.
Engine (e.g., E, A codes): Fuel system warnings, exhaust temperature, or AdBlue/SCR system faults. Hydraulics: Valve malfunctions or pressure drops. Valtra Error Codes (Editor's Choice)
A Valtra error code (or fault code) identifies specific malfunctions in a tractor’s systems, such as the engine, transmission, or hydraulics. These codes are typically displayed on the dashboard (like the Proline instrument panel) or a pillar display unit Common Valtra Error Codes & Meanings
Codes often use a letter prefix followed by numbers to categorize the fault: A-Prefix (Tractor Control Unit):
Signal from the gas pedal position sensor is outside the normal voltage range (
Often indicates a hydraulic or transmission issue, possibly due to low oil levels. E-Prefix (Engine/Hydraulic Systems): E290 & E393:
Commonly associated with hydraulic system malfunctions or sensor communication failures. Engine & Intake (SisuDiesel): 116 / 105: Intake manifold temperature is above normal ( Low engine oil pressure. Intake manifold pressure drop is too high during cranking. Transmission & Linkage:
A time-out error where the lift control unit is not receiving messages over the CAN bus. Flashing Powershift Indicator:
Signals transmission faults often linked to faulty hydraulic valves or sensors. Diagnostic Resources
If you are writing a paper or troubleshooting, these technical guides are primary sources: Valtra Fault Codes and Diagnostics Guide (Scribd)
: Detailed troubleshooting for proportional valves and sensors. Valtra T-Series HiTech Operator's Manual
: Official instructions for proper operation and basic maintenance to prevent codes. EEM3 Faultcodes (SisuDiesel) : Technical breakdown of engine-specific sensor errors.
Valtra Tractor Error Codes Guide | PDF | Clutch | Throttle - Scribd
Understanding Valtra Error Codes: A Comprehensive Troubleshooting Guide
When a Valtra tractor experiences a technical issue, it communicates through a series of service codes displayed on the dashboard or SmartTouch screen. These codes are vital for diagnosing malfunctions in complex systems like the engine, transmission, and hydraulics. Understanding these codes can help you determine if a problem requires a simple reset or professional service from an official Valtra dealer. How to Read Valtra Service Codes
Valtra service codes often appear in a multi-part format (e.g., 000091-13-035) and scroll across the display in sections: First Part: Usually four zeros (e.g., 0000).
Second Part: Identifies the component (e.g., 0091 for the throttle).
Third Part: The Failure Mode Identifier (FMI), which describes the nature of the fault (e.g., 13 for calibration error). Fourth Part: A category identifier (e.g., 035).
To view active codes on older models, you can often enter a "Test Mode" or use the Agroline instrument panel to scroll through the fault memory. On modern SmartTouch displays, errors appear directly on the Tractor Health screen. Common Valtra Error Codes and Meanings
Valtra tractors use various prefixes (A, P, F, L) to categorize faults within specific control units. Engine and Sensor Faults (Sisu/AGCO Power)
Commonly referred to as EEM3 or EEM4 codes, these relate to the Sisu Diesel engine management system:
110/111: Coolant temperature sensor defect (Low or High signal). 121: Water detected in the fuel filter.
263-266: Fuel rail pressure issues (above or below normal range).
421-423: MPROP control faults, typically indicating an open or short circuit in the fuel high-pressure pump control. Transmission and Shuttle Faults
These codes often start with "P" (Proportional valve) or "L" and relate to the Powershift or DPS units:
P101-P105: Faults in the DPS proportional valves (P1, P2, P3). These often signal a short circuit or damaged wiring.
P107/P109: Forward or Reverse drive proportional valve current errors.
A311/A312: Gearbox oil temperature sensor reading is impossible (over 150°C or below -50°C).
L422: One shuttle direction has been engaged for over 3 seconds without full control activation. Hydraulic and Linkage Faults
The rear linkage system (Bosch TC1) uses its own set of "Flash Codes" or service codes:
Flash Code 17: Battery voltage is too high (over 19V), requiring an alternator check.
Flash Code 22: Position sensor signal is faulty or incorrectly adjusted.
Flash Code 31/32: RH or LH side draft sensor signal is too high or too low.
Flash Code 44: CAN bus time-out; the linkage control unit is not receiving data from the main tractor control unit. Immediate Troubleshooting Steps
If an error code appears, follow these steps recommended in the Valtra Operator's Manual: Valtra Rear Linkage Service Codes | PDF | Switch - Scribd
