CONTACT US
CONTACT US

Urmet 1131 Manual Full May 2026

Used to power additional monitors or CCTV cameras where the main intercom system requires a separate power source.

If you tell me the exact Ref number on your device (e.g., 1131/51, 1131/102), I can extract the precise wiring diagram, addressing table, or reset procedure from the official manual.

Introduction

System Components

Installation

  • Power Supply Unit Installation
  • Door Release Unit Installation
  • Electric Lock Installation

    • Configuration

  • Setting Up the Monitor (Optional)

    • Operation

  • Communication
  • Door Release

    • Additional Features

  • Volume Control
  • Event Log

    • Troubleshooting

  • System Reset

    • Technical Specifications

  • Power Supply Unit
  • Door Release Unit

    • Warranty and Maintenance

  • Maintenance

    • The Urmet 1131 is an analog, surface-mounted, 4+n wire intercom designed to replace models like the Urmet 1030 or 730. Key connections include CA (Call), 1 (Speaker), 2 (Microphone), 6 (Common), and 9/10 (Lock Release), with installation requiring careful mapping of existing wires to these terminals. For the full technical data sheet, refer to Intercoms R Us. Connecting and Replacing Old Intercom with New Urmet 1131 urmet 1131 manual full

    Urmét 1131 Manual: A Comprehensive Guide

    Introduction

    The Urmét 1131 is a popular intercom system used in various settings, including residential, commercial, and industrial environments. This manual aims to provide a comprehensive guide for users, installers, and maintainers of the Urmét 1131 system. In this piece, we will cover the features, installation, operation, and troubleshooting of the Urmét 1131.

    Features of Urmét 1131

    The Urmét 1131 is a versatile intercom system that offers a range of features, including:

    Installation

    Installing the Urmét 1131 requires careful planning and attention to detail. The following steps outline the installation process:

    Operation

    Operating the Urmét 1131 is straightforward. The following steps outline the basic operation:

    Troubleshooting

    Troubleshooting the Urmét 1131 requires a systematic approach. The following steps outline common issues and solutions: Used to power additional monitors or CCTV cameras

    Technical Specifications

    The Urmét 1131 has the following technical specifications:

    Conclusion

    The Urmét 1131 is a reliable and versatile intercom system that offers a range of features and benefits. By following this manual, users, installers, and maintainers can ensure optimal performance and troubleshoot common issues. For further assistance, please consult the manufacturer's website or contact a authorized dealer.

    Appendix

    The following diagrams and illustrations are provided to aid in the installation and operation of the Urmét 1131:

    By following this comprehensive guide, users can ensure optimal performance and get the most out of their Urmét 1131 intercom system.

    The Urmet 1131 is a classic analog door entry handset designed for 4+N (5-wire) systems. It is widely used in residential apartment complexes and is known for its "Electronic Call" tone, which distinguishes it from older models that used mechanical AC buzzers. 1. Key Technical Specifications System Type: 4+N audio (requires 5 wires).

    Call Type: Electronic tone (not compatible with old AC buzzer systems).

    Terminals: Features 9 distinct terminals labeled 1 through 10, including a "CA" terminal for the call line.

    Dimensions: Approximately 21.5cm (L) x 7.5cm (W) x 5.5cm (H). Material: White ABS plastic for wall-mount installation. 2. Wiring Diagram & Terminal Mapping If you tell me the exact Ref number on your device (e

    Unlike modern digital systems, the 1131 relies on specific functional wiring. When replacing an older unit, users are advised to map wires by function rather than color. Description 1 Speech In Earpiece/Speaker audio. 2 Speech Out Microphone audio. 6 Common Ground connection for audio and lock. 9 Lock Door release contact. 10 Lock Secondary door release contact. CA Call Incoming electronic call signal. 3. Installation & Replacement Guide

    Mark Existing Wires: Before removing an old handset, label every wire. A common tip is to cut the wire leaving a small bit of insulation on the old terminal to preserve the color-to-terminal map.

    Mounting: The unit should be mounted at a height of approximately 1.55m from the floor.

    Cable Preparation: Strip the wires and feed them through the rear opening of the handset base before securing it to the wall with the provided screws.

    Wiring: Connect the identified functional wires to the corresponding 1131 terminals (1, 2, 6, 9, 10, CA). 4. Compatibility & Troubleshooting

    Direct Replacement: The 1131 is a standard replacement for the Urmet 1133 Atlantico. For more modern styling, the Urmet 1140 Signo is also compatible.

    The "5 vs 6" Screw Issue: Some users report new units appearing to have only 5 screw positions; often, the screw for terminal 1 is simply missing from the factory and must be moved or replaced.

    Common Faults: If audio works but the door doesn't open, check the bridge or common wire on terminal 6. If the call doesn't sound, ensure the system uses an electronic generator; if it's an old buzzer system, the 1131 will not ring.

    For full technical documentation, you can search for the Urmet 1131 Installation Manual or view professional data sheets at Intercoms R Us.

    Are you planning to replace an existing handset, or are you troubleshooting a specific issue like no audio or the door not opening? Connecting and Replacing Old Intercom with New Urmet 1131

    If you are installing or troubleshooting, here is the core data from the Ref.1131 series (Typically the 2Voice 7” monitor or the Call module):