Link Download - Firstchip Fc1178bc

  • Go to "Parameter" tab:
  • Click "OK" to save.

    • | Error Code | Meaning | Solution | |------------|---------|----------| | Error 0x104 | Flash chip not recognized | Manually select the chip ID from the dropdown list. | | Error 0x120 | Bad blocks exceed limit | Check "Skip bad block scan" (only if drive is small). | | Error 0x303 | Driver not loaded | Reinstall the driver with antivirus temporarily disabled. | | Error 0x601 | Write protection enabled | Short the test points on the USB circuit board. |

    After scanning dozens of Chinese forums (including USBDev and MyDigit), the most reliable tool is FirstChip MPtools version 20220127 or later. Do not download "FC1178BC.exe" from random ad-heavy websites.

    Below is a minimal example that shows how to toggle a GPIO pin (assumed to be connected to an LED) using the FirstChip SDK. This can be compiled with the FirstChip IDE or with an open‑source toolchain.

    /* fc1178bc_blink.c
 * Simple LED blink for FirstChip FC1178BC
 * Author: Your Name
 * Date:   2026‑03‑26
 */
#include "fc1178bc.h"      // Header provided by the SDK
#define LED_PIN   P1_0      // Example: Port 1, bit 0
void delay_ms(unsigned int ms)
/* Simple software loop – not accurate, just for demo */
    while (ms--) 
        for (volatile unsigned long i = 0; i < 1200; ++i) 
            __asm__("nop");
void main(void)
/* Configure LED_PIN as push‑pull output */
    P1M0

    Compilation (FirstChip IDE)

    Programming

    | Board | Features | Approx. Price (USD) | |-------|----------|--------------------| | FC‑EVA1178 | QFN‑32 device, 128 KB flash, on‑board debugger, USB‑UART bridge | $38 | | FC‑EVA1178‑PRO | LQFP‑48 device, 256 KB flash, external 8 MHz crystal, 2 × CAN transceiver | $62 | | FC‑EVA1178‑IoT | Includes an ESP‑32 co‑processor for Wi‑Fi, 2 × external flash sockets | $78 |

    All boards come with a pre‑loaded Bootloader that supports firmware update over UART, USB DFU, or SPI flash.

    The FirstChip FC1178BC is a versatile controller used primarily in budget and deceptive USB drives. While it allows manufacturers to create cheap storage, it has become synonymous with fake capacity scams. If you are stuck with a corrupted drive using this chip, the FC1178 MPTool is your best chance at restoring it to working order—albeit usually at a much smaller, honest capacity than what was advertised on the label. firstchip fc1178bc link download

    Proceed with caution, backup any data you can before using the tool, and always verify the actual capacity of cheap drives using tools like h2testw once they are repaired.

    The FirstChip FC1178BC is a common USB 2.0 controller often found in budget-friendly flash drives. When these drives fail—showing "No Media," becoming write-protected, or displaying incorrect capacities—users typically need a Mass Production Tool (MPTool) to re-flash the firmware and restore the drive. 🛠️ Key Recovery Tools for FC1178BC

    To repair a drive with this specific controller, you will need two main utilities: ChipGenius: Used to verify that your controller is indeed a FirstChip FC1178BC

    . It provides the necessary "Flash ID" required to select the correct firmware. You can find it at USBDev.ru.

    FirstChip MpTools (I-T117x MPTool): The primary factory utility for low-level formatting and firmware reloading. 📥 Download Links (FirstChip MPTools)

    Depending on your drive's production date, different versions of the tool may be required. Most versions are hosted on community databases like USBDev.ru or FlashBoot.ru:

    Standard Build (V1.0.5.2): Recommended for most modern FC1178/FC1179 chips. Available at USBDev - FC1179 MpTools. Go to "Parameter" tab:

    Specific FC1178BC Build (V1.0.2.10): An older, stable version specifically targeted at the BC revision. Available at USBDev - FC1178BC MpTools.

    Latest Cumulative Updates: Often found in the file archives at FlashBoot.ru. 📖 Step-by-Step Repair Guide

    Warning: This process will permanently erase all data on the USB drive.

    Preparation: Connect the USB drive directly to a rear-panel USB 2.0 port on your motherboard. Avoid using front-panel ports or hubs, as they can cause power instability during flashing. Launch the Tool: Run FCMpTool.exe as an Administrator.

    Detect the Drive: If the drive is recognized, it will appear in one of the slots with a "VID-PID" of FFFF-1201 (typical recovery mode). Configure Settings:

    Click Settings. If prompted for a password, try leaving it blank or use 123456 or FCMP.

    Under Scan Level, select Clear for the first attempt. For deeper issues, use Standard Scan. Click "OK" to save

    If the Flash ID is unknown, ensure Auto Create ID is checked.

    Start Flashing: Click Start (F9). The process can take anywhere from 3 to 15 minutes depending on the NAND quality.

    Finalize: Once the status shows PASS, remove the drive and re-insert it. Windows should now prompt you to perform a standard format to make the drive usable again. AI responses may include mistakes. Learn more Flashing FirstChip FC1178BC USB2DISK Mass Storage Device

    The FirstChip FC1178BC is a popular controller chip used in USB flash drives (often found in "fake" or upgraded flash drives sold cheaply). If you are looking for the download link and guide, it is usually because you need to repair a corrupted drive or format a drive that Windows says "Please insert a disk."

    Here is the complete guide on how to find the correct software, download it, and use it.

    Related search suggestions provided.