Aovo Pro Firmware B01011k Download Updated | 2026 Update |

If your scooter is bricked or won’t connect via Bluetooth:

Note: This voids warranty unless done by an authorized service center.

If you have recently bought a brand new AOVO Pro, check your current firmware version in the app. If your scooter is running perfectly fine, there is often no need to downgrade.

However, if you are experiencing:

Then B01011k might be the solution you are looking for.

💬 Discussion: Have you flashed B01011k on your AOVO Pro? Did it improve your ride, or did you encounter issues? Let us know in the comments below!

Disclaimer: This post is for informational purposes. Modifying your scooter's firmware may void your warranty and could make the scooter illegal for road use in your jurisdiction depending on speed limits.

The B-01.0.11K firmware is a specific legacy version for the AovoPro M365 Pro clone. It is primarily sought by users to bypass speed restrictions and unlock a top speed of up to 45 km/h. Key Features of B-01.0.11K Firmware

Speed Unlock: Provides a "Speed limit value" option under Advanced Settings, allowing for speeds significantly higher than the factory default of 25–31 km/h.

Bug Warning: A known issue with this version is that the headlight can typically only be controlled through the mobile app, rather than the physical button on the scooter. Download and Installation Instructions

Since the official AovoPro app often removes this version in favor of restricted updates, users typically utilize a third-party app to perform a manual "downgrade" or selective flash.

Download the 365Go App: Available on the iOS App Store or Google Play Store.

Connect Your Scooter: Open the app and pair it with your AovoPro via Bluetooth. The default password is often 888888. Initiate Firmware Selection: Navigate to Settings > Firmware Upgrade. Look for Available Version. Select any available version to start the process. The "Downgrade" Trick:

Allow the progress bar to reach approximately 10%, then force-close the app. Reopen the app and go back to the firmware settings.

B-01.0.11K should now appear as a selectable option in the list.

Complete the Update: Select B-01.0.11K and let the installation finish completely. Post-Installation Settings Once the firmware is active, you can unlock the speed: Go to Advanced Settings. Locate Speed limit value. Adjust the setting to the desired maximum (up to 45 km/h). Important Safety & Hardware Notes

Battery Strain: Running at 45 km/h significantly increases battery drain and heat. Continuous high-speed use may lead to overheating or premature battery wear.

Hardware Limits: The AovoPro motor is typically rated for 350W; reaching 45 km/h pushes the hardware to its absolute limit, which can be dangerous on standard 8.5-inch tires.

Local Laws: Most regions restrict electric scooters to 25 km/h (15.5 mph) on public roads.

If you are having trouble with the app connecting, would you like tips on resetting the Bluetooth module or a list of alternative apps like M365 DownG?

AOVO PRO Electric Scooter For Adults Speed 35kmph Black Unisex

Unlocking Performance: AOVO Pro Firmware B-01.0.11K Update Guide

The AOVO Pro electric scooter is a popular choice for commuters, but many users look for ways to push past the factory speed limits. The B-01.0.11K firmware update (often referred to as a downgrade or "hack") is the most well-known method to unlock a top speed of up to 45 km/h (approx. 28 mph). aovo pro firmware b01011k download updated

While the standard AOVO Pro app typically restricts speed to 25 km/h or 31 km/h, this specific firmware version allows users to access "Advanced Settings" to increase that limit significantly. Key Features of Firmware B-01.0.11K

Unlocked Speed: Access to a 45 km/h (28 mph) speed limit option.

Advanced Settings: Greater control over the scooter's performance parameters through compatible apps.

Known Bug: On some models, the headlight can only be toggled via the app rather than the physical button after this update. How to Download and Install the Update

Standard firmware updates are usually handled through the official AovoPro App or the 365GO App, but getting the specific B-01.0.11K version often requires a specific workaround. 1. Use the 365GO App

Most users report that the official AovoPro App no longer lists older, high-speed firmware. You should instead use the 365GO App (Blue Icon) available on the App Store or Google Play. 2. The "10% Cancel" Trick

If your current firmware version is higher than 11k (e.g., version 13), you may need to force the app to show older versions: Connect your scooter via Bluetooth to the 365GO App. Go to Settings > Firmware Upgrade. Select any available version and start the update.

Crucial Step: Once the progress bar reaches exactly 10%, close the app completely.

Reopen the app. It should now list B-01.0.11K under "Available Versions". 3. Complete the Installation

Select B-01.0.11K and let the update finish to 100%. Once done, navigate to Advanced Settings and adjust the Speed Limit Value to your desired top speed. Safety and Performance Considerations

While unlocking more speed is tempting, keep these factors in mind:

The AOVO Pro firmware version B-01.0.11K is a specific version highly sought after by users for its ability to bypass standard factory speed limits. While the official AOVOPro App typically restricts speed to 25–31 km/h for safety and compliance, this specific firmware version allows for significantly higher top-speed settings. Key Features of Firmware B01011K

Unlocked Speed Potential: This version is primarily used to unlock the scooter's maximum speed, with some users reporting potential limits as high as 45 km/h (approx. 28 mph) in advanced settings.

Alternative App Compatibility: To access and install this specific version, users often use the 365GO app (blue icon) rather than the standard black-icon AOVOPro app, which may no longer offer the 11K version for download.

Advanced Parameter Tuning: Once installed, new options typically appear under "Advanced Settings," allowing for a higher "Speed Limit Value" than the factory default. Known Issues & Considerations

Lighting Bug: Users have noted a bug in this firmware version where the scooter's physical light can only be toggled via the app rather than the physical button on the handlebars.

Hardware Limits: While the software might allow for higher speed settings, the physical motor and battery (standard 350W for many models) may still limit actual performance or lead to faster battery drain.

Installation Method: Successful updates often involve a "trick" where users start a firmware update in the 365GO app, close it at roughly 10% progress, and then select the B-01.0.11K version from the "Available Versions" list. Download and Official Support

You can find the standard management tools for your scooter on the official AOVOPro website or download the AOVOPro app for standard updates and locking features.

It looks like you're looking for the Aovo Pro firmware version B01011K (likely for an electric scooter model like the Aovo Pro ES80 or M365 Pro clone).

Here’s what you should know:

Important: Avoid clicking on any “direct download link” websites claiming to offer B01011K – many are fake or malicious. Always get firmware through the official app. If your scooter is bricked or won’t connect via Bluetooth:

If you need to verify your current version or troubleshoot an update failure, let me know your exact scooter model (e.g., Aovo Pro ES80, ES10, M365 clone) and I can give more specific steps.

Drafting a post for the AOVO Pro firmware B01011K update requires caution, as this specific version is primarily used by the community for speed unlocking rather than general maintenance.

Below is a draft post you can use, highlighting the updated installation method and key features.

🚀 AOVO Pro Firmware Update: B01011K Download & Guide (2026)

Are you looking to unlock the full potential of your AOVO Pro electric scooter? Firmware version B01011K is widely considered the "holy grail" for users wanting to bypass the standard speed limits. ⚠️ Essential Update Note

The official AovoPro App (Black Icon) has recently optimized its firmware judgment and often does not offer the B01011K version for direct download anymore. To access this specific build, most users now rely on the 365GO App (Blue Icon). ✨ Key Features of B01011K

Speed Unlock: Allows users to increase the speed limit to roughly 40-45 km/h (25-28 mph) in advanced settings, compared to the standard 25 km/h.

Xiaomi M365 Pro Compatibility: Often compatible with M365 Pro clones.

Known Bug: Be aware that in this specific version, the headlight can sometimes only be toggled through the app. 📥 How to Install/Downgrade to B01011K

Download the 365GO App: Since the stock AovoPro App may block this version, use the 365GO App available on iOS and Android stores.

Connect Your Scooter: Ensure Bluetooth is active and your scooter is paired.

Navigate to Firmware: Go to Settings -> Firmware Upgrade -> Available Version.

Select B-01.0.11K: If it is not immediately visible, some users report success by starting a different update, force-closing the app at 10%, and then re-opening it to refresh the "Available Versions" list.

Configure Speed: Once installed, go to Advanced Settings and adjust the Speed Limit Value to your preference.

Disclaimer: Modifying firmware is done at your own risk. It may void your warranty and increase wear on the motor or battery. Always wear protective gear when testing new speed settings.

Can Aovo pro scooters be speed unlocked? : r/ElectricScooters

Firmware version B-01.0.11K for the AOVO Pro (a popular Xiaomi M365 clone) is frequently sought after because it is one of the few versions that supports a specific speed unlock Why Users Look for B-01.0.11K

Modern versions of the official AOVO Pro app have removed the ability to increase speed limits beyond factory settings. However, version B-01.0.11K is known in the enthusiast community for: Higher Speed Limits:

Enabling a "45 km/h" option (though physical speed usually caps around 31–35 km/h due to motor/battery limits). Legacy Support:

Working with older third-party apps like "365Go" which allow deeper setting access than the current official app. How to Access the Firmware (Updated Community Method) Since the official AOVO website

usually only pushes the latest restricted firmware, users often use a "downgrade" trick via the (available on the App Store): Download 365Go:

Connect your scooter to this app instead of the official AOVO app. Trigger Firmware List: Firmware Upgrade The "Interruption" Trick: Note: This voids warranty unless done by an

Some users report that starting an update and then closing/reopening the app forces the list to refresh, showing legacy versions like B-01.0.11K under the "Available Version" dropdown. Select version B-01.0.11K and let the process finish. Important Warnings Lights Bug:

This specific firmware version has a known bug where the physical headlight button on the scooter may stop working; the lights must be turned on/off via the app. Brick Risk:

Flashing firmware carries a risk of "bricking" (permanently disabling) your scooter's controller. Ensure your scooter is fully charged and do not disconnect Bluetooth during the process. Hardware Limits:

Even if the app says 45 km/h, the AOVO Pro's 350W motor and 36V battery typically cannot exceed 35 km/h (approx. 21-22 mph) under real-world load. Are you currently having trouble connecting your scooter to the app, or do you already have the installed?

AOVO Pro Firmware B.01.01.11k is a specific software update designed for the AOVO Pro (M365 clone) electric scooter, primarily aimed at improving battery management and motor controller efficiency. Key Features and Changes BMS Optimization

: This version focuses heavily on the Battery Management System (BMS), aiming to provide more accurate battery percentage readings and prevent sudden power drops when the battery is low. Speed Stability

: Users report a smoother acceleration curve compared to older "v" or "m" series firmware, reducing the "jerky" feeling when engaging the throttle. Safety Lock Fixes

: Addresses bugs where the electronic lock via the AOVOPro app would occasionally fail to disengage or cause Bluetooth sync errors. Performance Review Range Maintenance : Unlike some performance-heavy custom firmwares, the

does not significantly "overclock" the motor, which helps maintain the scooter's standard 30-35km range. Hill Climbing

: There is a marginal improvement in torque when climbing inclines at lower battery levels (below 40%), as the firmware manages voltage sag more effectively. App Compatibility : This version is fully compatible with the official AOVOPro app

(available on iOS and Android), ensuring that settings like cruise control and speed limits (25km/h or 31km/h) remain customizable. Critical Considerations Installation Risk

: Firmware updates on AOVO scooters carry a risk of "bricking" the dashboard if the Bluetooth connection is interrupted. Ensure your phone stays within one meter of the scooter and has at least 50% battery. Regional Variations

: Depending on your specific model (e.g., the 2022 vs. 2023 manufacturing batches), this firmware may be the "final" stable version available before the hardware transitioned to newer controller chips. Official vs. Custom

: This is an official stability update. If you are looking for "speed hacks" to exceed 31km/h, this firmware will likely prevent those modifications as it reinforces manufacturer limits. step-by-step guide on how to safely flash this firmware using the AOVOPro app?

Dashcam value lies in reliability — footage is only useful if it’s actually recorded and retrievable. Even without flashy new features, firmware that reduces corrupted files, improves power handling, and keeps timestamps accurate directly increases the device’s usefulness in real-world scenarios: accidents, insurance claims, or simply tracking trips.

Based on user reports, B01011K typically includes:

Aovo Pro B01011K is an incremental firmware update focused on stability, recording reliability, and a few convenience fixes. It doesn’t add major new features, but it makes the dashcam behave more predictably when you need it most.

Attention all AOVO Pro riders!

There is a renewed discussion in the community regarding the B01011k firmware version. Many users are looking to download this specific version to unlock specific features or fix bugs found in later updates.

Here is everything you need to know about the B01011k update, including the download link and installation guide.